محرك البناء الكمون QSM15 77C

Cummins QSM15 77C Construction Machinery Engine

Emission Certification China MEP CS III
Rating Types Restricted
All data is based upon the engine operating with fuel system, مضخة ماء, and with inlet restriction and exhaust restriction at or below
datasheet limits. The alternator, المعجب, optional equipment, and driven components are not included. Coolant flows and heat rejection data is
based on a coolant mixture of 50% ethylene glycol and 50% water.
All data is subject to change without notice.

Intake Air System
Maximum allowable air temperature rise over ambient at intake manifold (naturally
aspirated engines) or turbo compressor inlet (turbo-charged engines): *This
parameter impacts emissions, LAT, and/or altitude capability
30.6 delta deg F 17.0 delta deg C
نظام التبريد
Maximum CAC outlet temperature at less than or equal to 25 deg C (77 deg F)
ambient 122 deg F 50 deg C
Maximum allowable pressure drop across charge air cooler and OEM CAC piping
(IMPD) 4.0 in-Hg 13.5 باسكال
Maximum coolant temperature for engine protection controls 228 deg F 109 deg C
Maximum coolant operating temperature at engine outlet (max. top tank temp) 225 deg F 107 deg C
Heat rejection to Charge Air Cooler* at Performance Table RPM points: السلطة المحكومة: 107 كيلوواط (6076 BTU / min) Peak Torque: 71.5 كيلوواط
(4065 BTU / min) *Heat Rejection to CAC is collected at standard engine test conditions of 25 deg C / 77 deg F turbo air inlet temperature.
Please refer to the discussion section in the Advisor Installation Requirement (AIR) Report for Compressor Outlet Temperature and CAC
Heat Rejection adjustment procedures for other test conditions.

Exhaust System
Maximum exhaust backpressure imposed by exhaust system (if DPF is present, the
limit is at soot level after regeneration or cleaning) 3.0 in-Hg 10.0 باسكال
Recommended exhaust pipe size (inner diameter) 5.0 في 127 مم
Maximum exhaust backpressure imposed by exhaust system for alternate pipe
قطر الدائرة (if DPF is present, the limit is at soot level after regeneration or cleaning) 3.0 in-Hg 10.0 باسكال
Alternate exhaust pipe size (inner diameter) 4.57 في 116 مم
RPM for maximum exhaust backpressure 2000 RPM 2000 RPM
Lubrication System
Nominal operating oil pressure at minimum low idle 18.9 رطل 130 باسكال
Nominal operating oil pressure at maximum rated speed 39.2 رطل 270 باسكال
Minimum engine oil pressure at minimum low idle (for engine protection devices) 10.0 رطل 69 باسكال

نظام الوقود
*Fuel cooling requirements with diesel fuel
Maximum supply fuel flow 430 lb/hr 195 kg/hr
Performance Data
أقصى سرعة منخفضة الخمول: 1200 RPM
الحد الأدنى من السرعة البطيئة منخفضة: 600 RPM
القدرة القصوى السرعة الزائدة: 2625 RPM
Maximum continuous power: 406 كيلوواط (544 حصان)
Maximum continuous speed: 2000 RPM

Cranking System (Cold Starting Capability)
Minimum cranking speed: 100 RPM
Maximum OEM parasitic load at 0 deg F and minimum cranking speed with all
required starting aids before over crank protection limits. 443 lb-ft 600 N-م
Maximum OEM parasitic load at 10 deg F and minimum cranking speed with all
required starting aids before over crank protection limits. 443 lb-ft 600 N-م
Required Starting Aids: Intake Air Heater Required, None
Minimum ambient temperature for unaided cold start at maximum OEM parasitic load 5.0 deg F -15.0 deg C
Minimum ambient temperature with grid heater only at maximum OEM parasitic load -31 deg F -35 deg C
Minimum ambient temperature with coolant and lube heater at maximum OEM
parasitic load -42 deg F -41 deg C

ما سبق هو معلومات technicial العامة للالكمون QSM15 77C محرك التطبيقات الصناعية. بل هو أيضا بالنسبة لنا لتوريد الكمون QSM15 77C قطع الغيار الأصلية وحدات المحرك مع ASSY مخلب.